EPDM membrane
A 45 or 60 mil EPDM sheet is installed in black or white.
Flat Roofing
Rubber Roof Installation Fairview, NJ
Installing a rubber roof in Fairview means choosing the EPDM thickness and attachment method, then flashing walls, curbs and edges so the membrane can move without tearing, with as few seams as possible. Call (551) 378-0045 to reach a local roofer.
EPDM is the material most people mean when they say rubber roof. The membrane is thick, stretchy rubber that tolerates temperature swings and resists hail and sunlight well. Its seams are joined with primer and tape instead of hot air.
The first decision is how the membrane is held down. Fully adhered roofs bond the whole sheet to the cover board with adhesive, mechanically attached roofs use plates and fasteners along the seams and ballasted roofs hold a loose sheet down with river stone. Residential roofs are most often fully adhered.
Two more decisions round out the plan. Thicker 60 mil membrane stands up better to foot traffic and hail. Black EPDM absorbs heat, which helps in cold climates, while white EPDM reflects sun and keeps rooms below cooler. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
If the problem goes deeper than it first looked, a Fairview roofer may also recommend rubber roof repair or flat roof installation.
Looking for Fairview rubber roof installation? Call (551) 378-0045 and describe the problem to a roofer who works in Fairview.
Call nowThe process
How rubber roof installation works
Each layer is set up to give the membrane a smooth, solid base.
Prepare the deck
Damaged decking is replaced and drainage is confirmed before any insulation goes down. On a replacement, old layers come off first.
Add the cover board
Polyiso insulation and a cover board create a flat, firm base for the rubber. Slope can be built in at this stage.
Roll out the membrane
The EPDM is unrolled, positioned and left to relax so wrinkles flatten before any adhesive goes on. Laps are arranged so water flows over them.
Adhering
Contact adhesive goes on the board and the membrane, and once it is tacky, the sheet is laid down and brushed. Each half gets the same treatment in turn. Brooming from the middle outward pushes trapped air to the edges.
Seaming
Seam areas are cleaned and primed, then seam tape is applied and rolled firmly with a seam roller. Lap sealant goes along exposed tape edges.
Flash the details
Perimeter edge metal, wall flashing and pipe boots complete the roof. Counter flashing covers the top of wall flashing. Before the crew leaves, seams are probed for any loose spots.
What is included
Parts of a new EPDM roof
Edge metal
Termination bar, pipe boots and edge metal are installed to keep water out.
Deck preparation
Decking is inspected and replaced where needed for a sound start.
Seams
Laps are joined with seam tape for a lasting bond.
Insulation
A cover board protects the insulation and gives the adhesive a firm grip.
Related service
EPDM Roof Installation Fairview, NJ
Installing EPDM well comes down to preparation, seams and flashing. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Weather matters too, since adhesives and primers need dry conditions. Some installers use water-based adhesive for the field of the roof and solvent-based adhesive at walls and curbs, where the grip has to be strongest.
In Fairview, an experienced EPDM installer leaves room for the membrane to move and age. Perimeter securement and proper flashing help prevent the shrinkage problems older rubber roofs show. It is worth asking how the edges will be secured.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Fairview are common on porches, garages, additions and flat sections of older homes. Across Fairview and nearby towns like Cliffside Park, Ridgefield, Edgewater and Palisades Park, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, so installation details matter as much as the material.
Searching for rubber roof installation near me from Fairview or Cliffside Park, Ridgefield, Edgewater and Palisades Park? Call (551) 378-0045 to talk to a roofer who works in your part of town.
How the weather here affects roofs around Fairview
Cold winters bring snow, ice and a long stretch of freezing nights. Heat escaping from the attic melts snow on the upper roof, and the water refreezes at the colder eaves, which is how ice dams form and back water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. That is why roof repair in Fairview is busiest after a hard winter and before the next one.
Why call
Why act early
Less damage
Small roof problems caught early usually stay small repairs.
Roofers who know Fairview
Local roofers see the same roofs and storm damage across Fairview and nearby towns.
Know what happens next
Ask your questions before you agree to anything.
Rubber Roof Installation questions
Can a rubber roof go over an existing roof?
EPDM can sometimes go over an existing roof. Codes generally allow one recover over a dry, sound roof. Otherwise, a tear-off is needed. Core samples or a moisture scan show whether the old roof is dry enough.
What is the difference between EPDM and TPO?
They are related but not the same. EPDM uses taped seams and stays flexible in cold, and TPO uses welded seams and reflects heat. A roofer can help you choose.
Which EPDM thickness should I choose?
The common choices are 45 mil and 60 mil. Thicker 60 mil is tougher and longer lasting. Even thicker sheets are available for demanding roofs.
Should my rubber roof be black or white?
The choice depends on the climate and the space below. White helps in sunny climates, and black is common where winters are long. A roofer can recommend what fits your home.
What is the lifespan of a new EPDM roof?
Rubber roofs often last decades. Regular inspections help it reach its full life. Small repairs are easy to make.
More questions? Call (551) 378-0045
Other services that may help
Rubber Roof Repair
Fixing open seams, punctures, shrinkage and split flashing on EPDM rubber roofs, after the real leak point is found.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, so water drains instead of ponding.
Learn moreTPO Roofing
TPO membrane roofs installed over new insulation or in place of a worn flat roof, built around proper drainage, flashing and edge metal.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, so ponding and repeat leaks end for good.
Learn more
Looking for something else?
See all roofing servicesTalk to a Fairview roofer about rubber roof installation
Call (551) 378-0045 to talk to a roofer serving Fairview, NJ.